W22 AHD 1080p Camera

Powerful. Compact. Outstanding Video.

  • 1080P (1920 x 1080) @ 30 fps
  • True WDR – Wide Dynamic Range
  • 12 IR LEDs for illumination at night
  • Vandal resistant metal housing
  • IP 67-dust and water proof-exterior mounting
  • Auxiliary bases available for easy aiming
  • Easy installation and integration with Gatekeeper DVRs

Exceptional Picture Quality In Any Light

The W22 AHD is a 1080P (1920×1080) High Definition, low profile, color day / night camera. The camera produces stunningly clear images in the most demanding conditions by utilizing a Sony EXMOR 1/3” CMOS Sensor.

Built rugged, the camera is designed to operate over the extreme temperatures and vibration found in vehicles. The W22AHD metal housing makes the camera vandal resistant and virtually immune to tampering.

The W22 AHD camera is designed to be mounted externally, on the side of a vehicle either facing towards the front of the vehicle or towards the rear. It is ideally suited as an overview camera for the SP25.

The W22AHD camera is plug compatible with Gatekeeper’s AHD mobile DVR’s utilizing Gatekeeper’s standard molex terminated analog cables. This is the same cabling used with Gatekeeper’s NTSC analog cameras. Cable length of 15’, 30’ and 60’ with strain resistant over molded connectors are available. This makes upgrading a vehicle from NTSC analog cameras to AHD cameras very easy as existing analog cables can be reused.

The W22AHD is IP67 – dust and water proof for exterior mounting while maintaining an operating temperature range of -40°F to +158°F, (-40°C to +70°C)

Camera – Housing Features:

Integrated IR

The integrated IR utilizes 12 infrared LED’s to provide IR illumination at night. A sensor in the camera detects the ambient light and automatically turns on/off the IR LED’s as needed.

Tamper Proof Adjustments

Not only is the camera constructed of metal but there are set screws that when tightened, prevents the camera aim from being tampered with. This is important for installation where the camera can be accessed, either due to low ceilings or accessible camera placement.

All Metal Housing

An all metal housing creates a vandal proof package that is resistant to physical damage.

90 Degree Aiming

The housing profile has been carefully designed so that the camera can be aimed 90° laterally and have a clear field of view. This is important for correct aiming when the camera is located at the front of a bus.

Sealed Design

The W22AHD is IP67 rated – dust resistant and water spray resistant.

Vibration Damping

In order to help reduce camera vibration, a rubber mounting pad is supplied. The rubber ring is installed between the camera base and the mounting surface. The rubber ring conforms to the camera base for easy alignment and quick installation.

Flexible Cable Routing and Mounting Options

The W22AHD camera is secured with 3 screws that are not accessible once the installation is complete. The camera’s signal cable can be routed directly up through the camera base, so that it’s not exposed.

     Imaging Sensor Sony 1/2.8” CMOS
     Processor Nextchip NVP2441
     Minimum Illumination 0.1LUX/F1.2 (no IR),  0.0LUX (IR On)
     Resolution  1080P (1920×1080), 720p (1280X720), WD1 (928X480), WHD1(928X240), WCIF (464X240), D1 (704×480), HD1 (704×240), CIF (352×240) DVR Dependent
     Image  1920 x 1080
     Sync  50/60 Hz
     Video Output  1.0V P-P/75Ω, NTSC
     S/N Ratio  ≥50db (AGC off)
     Electronic Shutter  1/30 to 1/100,000, second
     Gamma Correction  0.45
     AGC:  Auto
     White Balance  Auto
     BLC  Auto
     Capture Range
     Capture Speed
 Audio  No Audio
 IR  12 LEDs (850nm) with integrated on/off sensor
 Housing  Gatekeeper’s W1 camera housing
 Lenses Available  2.5mm, 2.8mm, 3.6mm, and 6.0mm
     Voltage Consumption  12v nominal  210 mA @ 12v IR On
     Dimensions  2.3” high x 4.3” base diameter (6cm x 11cm)
     Weight  .5 lbs (215 g)
     Operating Temperature  -40°F to +158°F (-40°C to +70°C)
     Operating RH  Under 90% non-condensing
     Adaptor Plat

W22 Product Sheet